TRUSTED WORLDWIDE BY FIRMS SUCH AS
CR-400
Next Generation, LTE-based Fleet Management Device with BLE Connectivity
The Cellocator CR-400 is Cellocator’s next-generation fleet and security management device and is based on the LTE Cat M1 network with 2G fallback.
The CR-400 is a high-quality, yet cost-effective and easy-to-install device, with built-in BLE connectivity and LED indicators. It is equipped with a large rechargeable backup battery (1000mAh) and includes basic driver behavior capabilities and built-in motion sensors that enable movement and towing detection to ensure improved compliance with vehicle security requirements.
The CR-400 works with Cellocator’s Open Protocol Standards (OPS) - a collection of scalable and secure data exchange options that enables you to access device data quickly and efficiently in order to eliminate lengthy integration projects and quickly integrate into your existing cloud solution to meet your business needs.
Features:
- LTE Cat M1 network with 2G fallback
- Built-in BLE connectivity
- 2 LEDs for Cellular/GNSS installation validation indication
- Basic driver behavior capabilities
- Large backup battery with an extended capacity of 1000mAh
- Memory that can store up to 7,000 logged events in offline scenarios
- IOs:
- Ignition switch input
- 2 programmable Inputs (digital/analog/frequency counter)
- 2 programmable I/O (dry contact/output)
- RS-232 serial port for accessories/programming
- 1-wire interface – Dallas port (driver ID/trailer ID and for 1 external temperature sensor)
- Built-in motion sensor for movement & towing detection
- Additional advanced capabilities, including:
- Crash detection
- Up to 100 Geo-Fences
- GNSS (GPS + GLONASS) Geo Location
- Cell-ID based geo location (alternative to GNSS when not available)
- In-cabin speed alert (activation of one output if speed limit is exceeded)
- Up to 100 roaming list
- Usage / frequency counters
- Curve smoothing
- Gradual immobilizing as one of the outputs
- Basic satellite activation
- Easy to install
-
Specs
LTE Dual mode CAT M1
Secure BLE4, wireless connectivity with PC and smartphones; BLE5 ready (future firmware update)
90.8x70.5x22.9mm 3.57”x2.78”x0.90”
130gr 4.6oz (unpacked, without harness, battery included)
3 Inputs (Input type: Analog, Digital), 2 outputs, 1wire input, RS232 serial
9-32VDC
Li-Ion Polymer, 3.7V, 1000mAh,
rechargeable3D, 16g range, 12 bit representation,
1mg resolutionCompliant with ISO 7637 test level #4 (in accordance with e-mark directive)
-30°C/-22°F to +70°C/158°F full performance
IP40 (IP 66 with protector)
ISO 16750
FCC / PTCRB / CE / IC / EN12830
(1-wire temperature sensor rating) -
Accessories
-
https://cdn.cellocator.com/wp-content/uploads/product_1wire_proximity_750x750.jpg
1-wire Proximity Reader
With a thin and compact enclosure, the 1-wire Proximity Reader serves as an external wireless front-end for the Cellocator unit, providing a wireless driver ID solution with support for proximity cards or tags.
Learn More about 1-wire Proximity Reader -
https://cdn.cellocator.com/wp-content/uploads/product_keypad_750x750.jpg
Cellocator Keypad
The keypad is used for driver authentication and vehicle immobilizer. The driver enters their driver ID using the keyboard, which transmits the ID to the Dallas input of the Cellocator unit.
Learn More about Cellocator Keypad -
https://cdn.cellocator.com/wp-content/uploads/product_dallas_reader_750x750.jpg
Dallas Kit (Reader & Keys)
Dallas Keys are coded keys used for driver identification and immobilizations, which are read via the Dallas reader, and which are connected to the 1-wire interface of the Cellocator unit. Additional keys enable multiple drivers.
Learn More about Dallas Kit (Reader & Keys) -
https://cdn.cellocator.com/wp-content/uploads/accessories_dallas_reader_with_led_push.png
Dallas Reader with LED & Push Button
This device contains a Dallas reader, a push button and a LED and provides driver identification and driver status reports on special events, such as business or private usage of a vehicle.
The Dallas reader is used for the Driver ID report, the push button is used for special event reports, and the LED is used as a status indicator controlled by the Cellocator unit.
Learn More about Dallas Reader with LED & Push Button -
https://cdn.cellocator.com/wp-content/uploads/product_trailer_ID_750x750.jpg
Trailer ID
The Trailer ID is a compact device for monitoring a trailer’s location and connectivity.
Fleet managers can easily monitor which trailer is connected to which vehicle within the fleet, or whether a trailer is even connected.
Learn More about Trailer ID -
https://cdn.cellocator.com/wp-content/uploads/product_1wire_temp_750x750.jpg
1-Wire Temperature Sensor
The 1-wire Temperature Sensor can be connected to the 1-wire port of the Cellocator unit to provide a low-cost, easy to install solution for the cold chain transportation market.
Operating temperature range: -55°C to +125°C
Learn More about 1-Wire Temperature Sensor -
https://cdn.cellocator.com/wp-content/uploads/product_analog_temp_750x750.jpg
Analog Temperature Sensor
The Analog Temperature Sensor is available in 5m and 20m lengths and connects to the analog input of the Cellocator unit. Temperature range: -40ºC to +75ºC.
Learn More about Analog Temperature Sensor -
https://cdn.cellocator.com/wp-content/uploads/product_fuel_cap_750x750.jpg
Fuel Cap Protector
The Fuel Cap Protector decreases the possibility of fuel theft by disabling access to the fuel tank when closed, and reporting on fuel cap openings via the unit’s digital input.
Learn More about Fuel Cap Protector -
https://cdn.cellocator.com/wp-content/uploads/product_concrete_750x750.jpg
Cellocator Concrete Mixer Sensor
The Concrete Mixer Sensor provides a smart solution for the construction vertical market.
Using this accessory increases concrete mixer efficiency, while ensuring high standard cement delivery and the reducing of costs by detecting fraud.
Learn More about Cellocator Concrete Mixer Sensor -
https://cdn.cellocator.com/wp-content/uploads/product_cr_protector_750x750.jpg
Cello & CR Family Protector
The Cello and CR Family Protectors are silicone/ rubber covers for Cello and CR devices, designed to improve the protection of devices (Cello family from IP40 to IP66 and CR from IP40 to IP65).
Learn More about Cello & CR Family Protector -
https://cdn.cellocator.com/wp-content/uploads/product_power_surge_750x750.jpg
External Power Surge Suppressor
The External Power Surge Suppressor provides adequate protection against exceptional electrical disturbances in the vehicle environment. It should be applied between the vehicle’s power source and the Cellocator unit. It is recommended to use it in vehicles where extreme electrical disturbances are expected.
Learn More about External Power Surge Suppressor -
https://cdn.cellocator.com/wp-content/uploads/product_door_sensor_750x750.jpg
Container Door Sensor
The Cellocator Door Sensor is a massive and rugged device used to detect the opening of doors, especially in container/trailer applications. The Door Sensor can be used with any Cellocator device equipped with a digital input.
Learn More about Container Door Sensor
-
- Applications